Product Overview
Options
Power- | Voltage- | Current-Range
Downloads

Options and Functions for the G5.RSS Series

The TFE time-based function generator allows programming either through G5.Control operating software, HMI touch display, or various interfaces.

  • Time-dependent functions U = f(t), I = f(t),
    P = f(t): sine, triangle, or square as well as user-
    defined data points. Import and export through
    CSV files supported
  • Ramp function for amplitude and offset changes
  • Small signal modulation up to 10 kHz

Sweep functionality for TFE
As an add-on to the TFE time-based function generator, the sweep mode allows for continuous or stepwise sweeping of the amplitude and the frequency of a programmed function. Both the amplitude and the frequency may be swept linearly or exponentially. This sweep function together with the high modulation bandwidth of 10 kHz makes devices well suited to electrochemical impedance spectroscopy (EIS) of batteries, fuel cells, and electrolyzers.

Order Code: TFE

G5 Time Base function – timing option for REGATRON programmable power supplies

The AAP application area programming feature allows to set the DC output voltage or current or power as a function of any of the input values IDC, UDC, or PDC. The functional relationship is given by a user-defined curve whose values are managed by CSV import/export. In this way, a wide variety of nonlinear electrical two-pole networks can be defined, e.g., photovoltaic arrays or fuel cell curves. The figure shows the typical fuel cell characteristics with a voltage/current dependence. Embedded calculation on board the G5.RSS assures real-time simulation.

Order Code: AAP

G5 AAP fuel cell test system diagram – REGATRON programmable power supplies in fuel cell applications
AAP curve with fuel cell characteristic U = f(I).

The HMI built into the front panel allows comprehensive and convenient operation of the power supply via touch display or the WebAPI (REST) interface. With the remote control unit (RCU) it is possible to control the device or system from a distant location in the same manner as with the HMI.

Order Code: HMI | RCU

G5 HMI Remote Control Unit – user interface option for REGATRON programmable power supplies

The CAN multi-protocol (CANmp) interface has a 1 kHz data rate, a 16-bit resolution, and is adaptable to any proprietary CAN bus. In addition, it supports dbc file handling.

Order Code: CANmp

The EtherCAT slave interface (ECAT) supports configuration by ESI file and communicates in a 1 kHz cycle. It transmits the entire process data in the same cycle, i.e. commands, actual states, and actual values. Acyclic communication via mailbox for device configuration is also possible. 

Order Code: ECAT

SCPI, Standard Commands for Programmable Instruments, are ASCII s trings, which are sent to the device over TCP/IP using the LAN socket. They can perform set operations or query operations.

Order Code: SCPI

Integrated safety relay (ISR) for increased emergency stop reliability supporting performance level PL c / PL e according to EN ISO 13849.

Order Code: ISR

Discharging of the AC filter (XCD), is mandatory when using the device with a plug connection. XCD ensures a discharge time of the AC filter less than 1 s as required by EN 62477-1

Order Code: XCD

Based on the 80 V models, also a 60 V SELV version is available.

order code example: G5.RSS.9.60.338

The different protective covers are designed for integration into 19″ rack systems or for use as a tabletop device. The cover for cabinet integration provides protection against accidental contact, whereas the cover for the tabletop version requires touch-proof protection in accordance with standard EN 62477-1.

Order Code: PAC

G5 protection covers – safety accessories for REGATRON programmable power supplies

Front panel mounted air filter (AirFilter), recommended for use in dusty environments and with IP20 cabinets

Order Code: Airfilter

Liquid cooling of the G5 devices is available at system level. The Regatron solution allows to take the entire dissipated heat of the power supply out of the test bench and reuse it as process heat in the facility if possible.

G5 liquid cooling option – efficient thermal management for REGATRON programmable power supplies
REGATRON’s liquid-cooled system solutions up to IP54 with various power levels e.g. 54…162 kW (left) and 216…324 kW (right). The re-mote control unit RCU, indicator lights, emergency stop button, and main switch allow the user to operate the system on the enclosure's front door.
  • Mobile rack solutions on castors up to 162 kW
  • Stationary rack solutions up to 324 kW
  • IP54 protection for air or liquid-cooled systems
  • Third-party product integration and numerous safety options
  • Insulation monitoring: remote activation of the insulation measurement, actual insulation value, and warning/error status are provided by the CANmp interface or by optional display
  • Easy reconfiguration between parallel, series, and mixed operation
Rack integrated system solution G5 – modular REGATRON programmable power supply setup
REGATRON’s rack-integrated turn-key system solutions for vari-ous power levels e.g. 72 kW (left) and 162 kW (right). Various types of AC/DC connectors and cables allow for comfortable handling.
Contact REGATRON – discover programmable power supplies and global support services

Benötigen Sie die richtige Energie-Lösung?

Wir helfen Ihnen dabei, die ideale Konfiguration zu finden. Kontaktieren Sie uns noch heute für kompetente, individuelle Unterstützung.